cnshunda

Even with the correct selection and installation of the hose, the service life of the hose may not be extended without a proper maintenance plan. The frequency of inspecting the hose or considering replacing the hose before the actual failure occurs depends on a variety of factors, including the following factors: the severity of the application, the possibility of failure, and past hose failure experience. If you have a proper maintenance plan, you need to make sure Everyone follows the maintenance plan correctly. Next, Hose Fittings Manufacturers introduces the maintenance method of hose fittings. The maintenance plan also requires users to take the following measures: Check hoses or fittings correctly. If you want to know whether your hoses are at risk of failure now or in the future, you need to perform a visual inspection. The hose assembly should be visually inspected on a regular basis. If you find any abnormality in the hose or fittings, you should not continue to use the machine until the hose or fittings are further inspected, repaired, or replaced. The following are some items that indicate the need to be replaced before using the machine: cracks or cuts on fittings or hoses burnt hoses or pipe fittings leaking soft caps or loose components during the inspection process, you may be aware of Some parts of the component require special attention because of the state. Some parts need to be replaced, tightened, or repaired. If you encounter any of the following conditions during the inspection, you need to take the necessary measures: Excessive dirt or other accumulations leaking Clips and protective covers worn Air retention It is important to ensure that the system you are using is operating at the highest temperature. Efficiency is important. Level. It is important to check for any leaks or malfunctions. When people test systems and machines, it is important to observe safety measures to avoid any harm. Inspectors need to ensure that the hose is only operating at maximum efficiency and not exceeding its efficiency. Because of the potential for overpressure, it is important to exercise caution when handling fluids. If you find that one or more hoses are malfunctioning, the system or machine should no longer be used and everyone should leave the area. If you just turn off the hydraulic pump, you may not be able to solve your problem. Certain components in the system may cause pressure to remain in the hose assembly. Even if the equipment is not operating as it should, the pressure will continue. If you find any holes in the hose, hydraulic oil may be sprayed out. These hydraulic oils can be very harmful, and pressure relief does not always happen quickly. After the pressure is relieved, the hose assembly can be removed. If any type of failure is identified, it is very important to remove it and replace it. In order to fully protect your system or machine, it is very important to check and replace parts correctly when you find a fault or a potential fault. Through the above introduction, Hydraulic Fittings Manufacturers hopes that you can simply refer to the content of this article in future use. https://www.cnshunda.com/

Hose Fittings Suppliers introduces the connection method of hydraulic hose: 1. The inner and outer threads of the quick connector can be connected with the hose only after using the transition joint or the adapter. 2. No matter there are many kinds of hose joints, it is necessary to choose how to use transition joints according to the type of hose joints. If the hose is an ordinary water pipe, it should use a transition joint, one end of the inner tooth, one end of the water pipe, and then fixed with a throat hoop. If the two ends of the hose are internal teeth, it should be used with the transition joint, one internal tooth and one external tooth. If the two ends of the hose are external teeth, it should be connected with the transition joint, and the internal teeth will be straight. 3. Generally, hydraulic quick-change joints need to withstand high pressure. Therefore, in most cases, high-pressure oil pipes are used. In most cases, both ends of the oil pipes are internal teeth, so they should be able to be connected directly. 4. As for the hydraulic joint, there is no need for other rubber rings to seal, and the product itself is concave at one end and convex at the other end, which can be completely sealed after connection. Through the above introduction, Hydraulic Adapters Wholesaler hopes that you can simply refer to the content of this article in future use. https://www.cnshunda.com/

Adapters Suppliers introduces the function of quick seal fittings: Sealing function: air tightness test, tightness test, etc., quickly seal the nozzle. Grabbing function: Pneumatic joints can also be used for automatic grasping, and the front sealing ring can grasp the product. Test function: vacuum, pressure, leakage, operation and other aspects of the test. Filling function: filling of inert gas, coal gas, natural gas, nitrogen, oxygen, PG, carbonic acid, etc. Connection function: It is mainly used to connect the nozzle and testing equipment during product quality testing, which plays the role of quick connection and disconnection. Through the above introduction, Hydraulic Fittings Suppliers hopes that you can simply refer to the content of this article in future use. https://www.cnshunda.com/

For hydraulic hose fittings, it is very important to maintain the pressure and tightness of the hydraulic system, which is mainly achieved through the contact surface of the connecting piece. Banjo Elbow Suppliers introduces four types of hose fittings: 1. Taper thread seal: After the inner and outer threads are connected, the seal is formed by the mutual extrusion of their tooth profiles 2. Soft seal: There is an O-ring on the external thread, through which it is extruded on the mating surface of the internal thread to form a seal, often used in high pressure systems, typical joints such as ORFS 3. Metal sealing: The sealing is achieved by squeezing and deforming each other through a certain angle of the metal contact surface. 4. Metal seal with O-ring: This sealing form is a combination of the front 2 and 3 seals, the metal slopes squeeze each other to seal, and the O-ring is deformed to form a seal. This sealing form is especially suitable for high-pressure hydraulic pressure. System, typical joints such as DKOL, DKOS. Through the above introduction, Hose Fitting Manufacturers hopes that you can simply refer to the content of this article in future use. https://www.cnshunda.com/

Stainless Steel Hose Fittings Factory introduces the installation arrangement of stainless steel elbows. The bolts of the stainless steel elbow valve packing gland need to be tightened evenly and cannot be pressed into a skewed state to prevent damage to the valve stem from obstructing and leaking. When using stainless steel elbows, be sure to keep them clean, and the threads of the transmission must be regularly lubricated. If a fault is found, it needs to be stopped immediately and put into use after the cause is found out and the fault is cleared. When installing, you can install the stainless steel elbow directly on the pipeline according to the connection method, and install it according to the location of use. Under normal circumstances, it can be installed on any position of the pipeline, but due to the need to facilitate the inspection operation, it should be noted that the flow direction of the stainless steel elbow is six upwards from the bottom of the valve disc, so the stainless steel elbow can only be horizontal installation. When installing stainless steel elbows, you need to pay attention to its sealing performance to prevent leakage, which will affect the normal operation of the pipeline. https://www.cnshunda.com/

Hydraulic pipe joints are mainly used to connect in the hydraulic system, so they are also in a relatively important position. After all, the pressure and impact force at the joints are relatively strong, and the requirements for the joints are also very high. In the use of hydraulic pipe joints, if there is a wrong operation, it is easy to cause irreversible consequences. Metric Thread Fittings Manufacturers introduces the precautions for using hydraulic pipe fittings: 1. Avoid using sealant and other items in the joint. Some people use sealant and other items inside or near the hydraulic joint in order to ensure the sealing of the hydraulic pipe joint. This can easily cause the pressure to increase sharply and break the phenomenon after the internal blockage. . 2. One-time installation. When installing hydraulic pipe joints, pay attention to the one-time installation, avoid multiple disassembly and assembly, which may easily cause leakage at the interface due to wear. 3. Post-installation test. After the hydraulic pipe joints are installed, the overall pipeline should be tested for transportation. The main purpose is to test whether there is leakage at the hydraulic joints and the overall impact resistance. 4. The environment near the joint is friendly, and the important significance of the hydraulic pipe joint also makes it have certain requirements on the environment. The surrounding environment temperature should be kept as stable as possible to avoid thermal expansion and contraction. At the same time, avoid corrosive gas nearby. Liquid, reduce the possibility of leakage caused by corrosion. Through the above introduction, BSP Thread Fittings Wholesalers hopes that you can simply refer to the content of this article in future use. https://www.cnshunda.com/

Today, Adapters Suppliers will introduce the maintenance methods of hydraulic accessories: When we need to clean up the hydraulic parts, don't disassemble it by ourselves. We need to ask a dedicated person to disassemble it. Otherwise, if any parts are damaged, it will not be worth the loss. Including the installation, it will also require specialized personnel to install it. After using the hydraulic parts for a period of time, we also need to carry out some quality inspections. We need to inspect them. Measure whether it is rusty, corroded, or deformed. These are all things we need to detect. Dust will definitely accumulate on hydraulic parts that have been used for a period of time, so we also need to clean up the dirt and oil on its surface. For some parts that need lubrication, we also need to add lubricant on a regular basis. www.cnshunda.com

Adapters Suppliers introduced that the connection between the two ends of the metal hose can also be made into other connection methods besides thread and flange standards, which is convenient for connection and use. Application of metal hose products: used as protection for various equipment signal lines, transmission wires and cables, and optical fibers and cables. There are roughly the following: 1. Wire protection tubes for armored optical cables, precision optical rulers, optical measuring instruments, medical instruments, and machinery and equipment. 2. It is suitable for public telephones, remote water meters, door magnetic alarms and other equipment that needs to be protected for wires. 3. Protective tubes for all kinds of small wires. 4. Network line protection tube for various computers, robots, etc. https://www.cnshunda.com/product/tube-fittings-ada...